If English is OK or you have already changed the language, switch on the printer by pushing the power switch. If there is no sound, or no light on the front panel, you have a power problem. If you want to change the language, hold ENTER on the front panel and then switch on the printer by pushing the power switch. When the word "English" appears on the front panel screen, press the up or down arrow until your language appears.
Task 4: Load media Because the next task is to load the cartridge s and perform the automatic cartridge alignment procedure, you must load opaque media at this stage; for example, load opaque bond printer paper for the HP Designjet printer or coated paper for the HP Designjet C Plus printer, as this is necessary for the alignment procedure.
A roll of suitable HP media is supplied with your printer. To load roll media, start with step 1 below. To load a roll Make sure the printer wheels are locked the brake levers pressed down to prevent the printer from moving.
Open the roll cover and remove the empty spindle by pulling firmly on each end. The two ends are different: one end has a media stop and the other end has a smaller end cap. Place the spindle vertically on the floor, with the media stop at the bottom, ready for the new roll. Remove the new roll from its wrapping. Remove the end cap from the top of the spindle, and slide the new roll onto the spindle.
The leading edge of the media must wind clockwise. If the media stop falls off, push it back in until it snaps into position. Push the end cap back in, making sure that the tabs are flush against the ends of the roll. Push it far enough to be firm, but do not use excessive force, as this may break the tabs.
Insert the spindle so that the large media stop is to the right and the small end cap to the left. Push in firmly on both ends.
Be sure the media remains flush against the media stop. Check the leading edge as it unwinds from the spool. If it is uneven, trim it as explained in step 7; otherwise go to step 8.
Keep fingers clear of the cutting path. Keep media cutting knife away from children. Use the media cutting knife in the pocket located at the back of the printer to cut off the first few inches of the media. Pull the media towards you, holding it from the sides, and align its right edge with the perforated line on the entry platen.
Press the down arrow next to the front-panel display to indicate you are loading a roll. Press the up or down arrow until the display shows the type of media you are loading; then press ENTER. HP Designjet printer: If you are using the roll supplied with the printer, scroll to Opaque bond. Take hold of the edges of the media now extending from the exit slot and pull the media toward you until taut. Then align the left and right edges of the media so that they are flush with the edges of the roll.
When the printer instructs you to close the roll cover, rewind the media stop clockwise to take up any slack in the roll. Make sure that the leading edge of the media is outside the roll cover, and then close the cover. Press down arrow to continue. The printer automatically trims off the first few inches of media. To load a sheet You can load a sheet in either portrait or landscape orientation.
Your choice of orientation is significant when sending a plot from your software, but for the moment it does not matter. Printing will be on the underside, so if loading coated paper, load the coated side down. Make sure the media lever is down and the roll cover is closed. Holding the media from the sides, align the right edge with the perforated line on the entry platen.
Insert the media until it buckles slightly; that is, push all the way to the media stops. Let go of the media when the printer begins to pull it in. Press the up arrow next to the front panel display to indicate you are loading a sheet. Press the up or down arrow until the display shows the type of media you are loading if you are using regular printer paper, scroll to Opaque bond; if using coated paper, scroll to Coated paper ; then press ENTER.
The printer moves the sheet in and out to check its size and alignment, and then advances it to the start of the page. Task 5: Load the print cartridge s Cartridge types caution: The HP Designjet printer is designed to operate only with the HP-approved cartridges supplied with the printer.
The HP Designjet printer is supplied with two black cartridges one is a spare cartridge. For the HP DeskJet C Plus printer, each stall in the carriage has a dot indicating the color of the cartridge that should be installed.
You must put the correct cartridge in the correct stall; otherwise, not only will your colors be wrong, but print quality may be affected. The sequence of the colors is, from left to right: yellow, cyan, magenta, and black. If you have color vision deficiencies, you can identify the colors of the cartridges by the part numbers on the boxes.
Keep hair, jewelry, clothing, and foreign objects away from the printer mechanisms. Keep new and used print cartridges out of the reach of children. To load the print cartridge s Proceed as follows:. Press Access Cartridge s and wait for the cartridge carriage to come to a complete stop next to the front panel.
Make sure that the printer is still switched on never install cartridges with the printer switched off. Insert the cartridge in the stall. Press down lightly and push the cartridge away from you until it snaps into place.
If the front panel display says Reseat cartridge s , then remove the cartridge and insert it again. Do so until the message disappears.
When the cartridges are successfully installed, the printer automatically runs the cartridge alignment procedure. You can throw away the small print produced during the cartridge alignment procedure.
Task 6: Print a demonstration plot optional Before you connect your printer to a computer, it is a good idea to print one of the internal sample plots. This ensures that the printer itself is operating properly.
If media is not already loaded, load a roll or a sheet, as explained earlier in Task 4. The Receiving light flashes while the plot is being processed; then the printer starts printing. After it has finished:. On roll media, the printer waits for the ink to dry, if necessary, and drops the plot into the media bin.
Drivers hp designjet c plus windows 7 ronnifinra For other applications, see below for advice, and if necessary, contact your software vendor. Set up the printer. Download the latest drivers HP Designjet c Plus drivers hot driverscollection. Has anyone been able to setup HP Designjet C plotter on I have only been able to by using Oracle virtual machine app Virtualbox and generating a Windows 7 machine and then using the driver for a HP plotter I think that was the model.
Hp c plus designjet driver fortibungclun's Ownd tip liase Designjet c plus driver download klipjohisci's Ownd trend daahdadan Good evening. Easy Driver Pro makes getting the Official Hp c plus driver for windows 8 driluperfa's Ownd best linneyce Easy Driver Pro will scan your computer for missing, corrupt, and outdated Drivers. That said, there is a 64 bit driver for the Designjet C that work in Windows 8, see the post here. Useful Blogs. Video Result.
Hp Plotter Designjet c plus ML Impresora Hp Plus Designjet Plotter You can find the drivers you need from here: HP Designjet Printer series. If you have any other questions I suggest posting in the Business Support forum since this is a commerical printer.
Go to www. Be sure to check the additional information, like how to install the driver or troubleshooting guides. Didn't find what you were looking for? Ask the community. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for.
Did you mean:. Need Windows 11 help? Check documents and videos on compatibility, FAQs, upgrade information and available fixes. Windows 11 Support Center. Create an account on the HP Community to personalize your profile and ask a question. Your account also allows you to connect with HP support faster, access a personal dashboard to manage all of your devices in one place, view warranty information, case status and more. While we prepare for the move, we are unable to accept new postings.
0コメント